Corrosive Materials CHP 6.2

6.2 Corrosive Materials

Many chemicals commonly used in the laboratory are corrosive or irritating to body tissue. They present a hazard to the eyes and skin by direct contact, to the respiratory tract by inhalation or to the gastrointestinal system by ingestion. 

pH - is a measure of acidity or alkalinity. Acids and alkalis are both classified as corrosives, so contact with them must be prevented.

Acids (pH values of 0 to 6.9)

• Usually cause immediate pain upon skin or eye contact and result in severe burns and permanent eye damage
• May be used in the workplace (nitric acid, pH3; sulfuric acid pH 2.75; and hydrochloric acid, pH 1.6)

Alkalis (pH values 7.1 - 14)

• Often do not cause immediate pain upon skin or eye contact
• Break down fatty acid skin tissues and penetrate deep into the body
• May be used in the workplace (potassium hydroxide, pH 10.98; ammonium hydroxide, pH 11.7; sodium hydroxide, pH 13)

Strong acids and alkalis are utilized around many homes. Muriatic acid, a common pool cleaner, has a pH of 2-3. Sodium hypochlorite, used as a drain cleaner, is a strong base with a pH of 12 or 13.

6.2.1 Corrosive Liquids

Corrosive liquids (e.g. mineral acids, alkali solutions and some oxidizers) represent a very significant hazard because skin or eye contact can readily occur from splashes and their effect on human tissue generally takes place very rapidly. Bromine, sodium hydroxide, sulfuric acid and hydrogen peroxide are examples of highly corrosive liquids. See the Safety Data Sheet for specific corrosive liquids such as Hydrofluoric Acid and Phenol.

The following should be considered:

1. The eyes are particularly vulnerable. It is therefore essential that approved eye and face protection be worn in all laboratories where corrosive chemicals are handled.

2. Gloves and other chemically resistant protective clothing should be worn to protect against skin contact.

3. To avoid a flash steam explosion due to the large amount of heat evolved, always add acids or bases to water (and not the reverse).

4. Acids and bases should be segregated for storage.

5. Liquid corrosives should be stored below eye level.

6. Adequate quantities of spill control materials are readily available in the laboratories. Contact the Chemical Hygiene Officer (x4019) if spill control material has been used during a spill cleanup. 

6.2.2 Corrosive Gases and Vapors

Corrosive gases and vapors are hazardous to all parts of the body; certain organs (e.g. the eyes and the respiratory tract) are particularly sensitive. The magnitude of the effect is related to the solubility of the material in the body fluids. Highly soluble gases (e.g. ammonia, hydrogen chloride) cause severe nose and throat irritation, while substances of lower solubility (e.g. nitrogen dioxide, phosgene, sulfur dioxide) can penetrate deep into the lungs. Warning properties such as odor or eye, nose or respiratory tract irritation may be inadequate with some substances. Therefore, they should not be relied upon as a warning of overexposure. Perform manipulations of materials that pose an inhalation hazard in a chemical fume hood to control exposure or wear appropriate respiratory protection. Protect all exposed skin surfaces from contact with corrosive or irritating gases and vapors. Regulators and valves should be closed when the cylinder is not in use and flushed with dry air or nitrogen after use. When corrosive gases are to be discharged into a liquid, a trap, check valve, or vacuum break device should be employed to prevent dangerous reverse flow. 

6.2.3 Corrosive Solids

Corrosive solids, such as sodium hydroxide and phenol, can cause burns to the skin and eyes. Dust from corrosive solids can be inhaled and cause irritation or burns to the respiratory tract. Many corrosive solids, such as potassium hydroxide and sodium hydroxide, can produce considerable heat when dissolved in water. Wear gloves and eye protection when handling corrosive solids. When mixing with water, always slowly add the corrosive solid to water, stirring continuously. Cooling may be necessary. If there is a possibility of generating a significant amount of dust, conduct work in a fume hood.